Skip Navigation Website Accessibility
 

Embellish - Bold Tearaway - Fusible

Size: 12" x 10 yds

Price:   $ 24.99   $ 17.49  
Quantity:
0 in Cart

Size: 15" x 10 yds

Price:   $ 28.99   $ 20.49  
Out of Stock

Size: 20" x 10 yds

Price:   $ 34.99   $ 24.49  
Quantity:
0 in Cart

Fusible Bold Tearaway

 

Embellish® Fusible Bold Tearaway is a tightly woven, heavy duty, fusible stabilizer made using a unique “Non-Woven” technique. The fusible coating is temporary, so it pulls away easily when ironed at the proper temperature. It is used to support decorative sewing stitches and large or dense embroideries on stable woven fabric such as: cotton, duck cloth, twill, and denim. It features a multi-directional tear capability, easily pulling away clean from the embroidery design, for a crisp look on the front and back. Also available in a non-fusible version, which is to be used as additional support by floating a piece under the embroidery hoop when the design stitch count is more than one layer of Embellish® Fusible Bold Tearaway can sustain.

EFBT-12 (12”x10 yds) / EFBT-15 (15”x10 yds) / EFBT-20 (20”x10 yds)

Embellish® Fusible Bold Tearaway is a tightly woven, heavy duty, fusible stabilizer made using a unique “Non-Woven” technique. The fusible coating is temporary, so it pulls away easily when ironed at the proper temperature. It is used to support decorative sewing stitches and large or dense embroideries on stable woven fabric such as: cotton, duck cloth, twill, and denim. It features a multi-directional tear capability, easily pulling away clean from the embroidery design, for a crisp look on the front and back. Also available in a non-fusible version, which is to be used as additional support by floating a piece under the embroidery hoop when the design stitch count is more than one layer of Embellish® Fusible Bold Tearaway can sustain.

Contents:

Made in America. Premium tearaway fibers using the Wet-Laid Non-Woven Process with a light temporary fusible coating. 2 oz.

Stitch Count:

Holds up to 12,000 embroidery stitches in a 4”x4” hoop.

To Use:

  1. Fuse one layer of the stabilizer to the back of the material. Be sure to use a piece at least one inch larger than the outer perimeter of the hoop to ensure proper stabilization.Important – Use a low temp (Silk Setting) on your iron. Do NOT touch the surface of your iron to Embellish® Fusible Bold Tearaway, press from the fabric side or use a press cloth (natural fibers such as muslin or cotton). All irons heat differently. The iron temperature given is a starting point. If you find that you are not getting a good fuse, slowly increase your iron’s temperature until you achieve a good bond between the fabric and stabilizer and ensure the stabilizer can be torn away easily. If it won’t release easily when torn away, the iron temperature is too high.
  2. Hoop the material along with the fused stabilizer, making sure the material and stabilizer are taut.
  3. If the design has more than 12,000 stitches in a 4”x4” hoop then “float” a piece of non-fusible Embellish® Bold Tearaway under the hoop for added support.
  4. Add an embroidery topper on top of the hoop (either Embellish® Rinse-Away Clear Topper or Embellish® Iron-Away Clear Topper).
  5. Embroider the design.

To Remove:

  1. Remove the material from the hoop. Remove the topper, following the topper product sheet.
  2. Hold your fingers over the bobbin thread and tear away as much of the stabilizer as possible, starting with the “floater,” if applicable.
  3. If the iron temperature was too hot during the fusing process, it might be necessary to re-heat the stabilizer, using a Silk Setting for it to release from the material.

Laundering and Care:

Launder and dry the item according to the fabric material fiber content.